Ask Latest Price
Verified Supplier
1 Years
Ningbo Kent Bearing Co., Ltd
Add to Cart
Description of Z3V3 ball bearings
These types of ball bearing can be used in agricultral machinery, construction machinery, transportation vehicles, etc. It is simple in design, has the features of low friction, high rotating speed and low noise, reliable in operation and low in maintenance cost.
Features of high precision ball bearings:
(1)High precision: It conforms to the national Z3V3 quality level and reaches the P5 and P4 precision levels. The higher the precision, the smaller the error, the strong consistency and the stable operation.
(2)Low noise: noise level detection, the decibel value of miniature bearings is <23 decibels, the decibel value of micro and small bearings is <25 decibels, and the decibel value of small bearings is <27 decibels, which is much lower than that of the peers.
(3)High Rotating speed: Bearing micron-level size control, p5 error < 6 microns, strong consistency, can be matched according to product requirements, to meet dozens of to 20,000 revolutions, or even higher speed requirements
(4)Durability: Control from raw materials, use more wear-resistant Xingcheng steel and Northeast special steel, and have a longer service life.
Technical Parameters:
Basic | Bore d | Outer Diameter D | Width W | Radius r | Basic Load | Maximum Run | Weight | ||||||
Dynamic | Static | Grease | Oil | ||||||||||
| mm | inch | mm | inch | mm | inch | mm | inch | C | CO | r/min | r/min | ||
604 | 4 | 0.1575 | 12 | 0.4724 | 4 | 0.1575 | 0.2 | 0.008 | 0.97 | 0.36 | 43000 | 51000 | 0.002 |
605 | 5 | 0.1969 | 14 | 0.5512 | 5 | 0.1969 | 0.2 | 0.008 | 1.33 | 0.505 | 39000 | 46000 | 0.0035 |
606 | 6 | 0.2362 | 17 | 0.6693 | 6 | 0.2362 | 0.3 | 0.012 | 2.24 | 0.91 | 28000 | 36000 | 0.008 |
607 | 7 | 0.2756 | 19 | 0.7480 | 6 | 0.2362 | 0.3 | 0.012 | 2.24 | 0.91 | 28000 | 36000 | 0.008 |
608 | 8 | 0.3149 | 22 | 0.8661 | 7 | 0.2756 | 0.3 | 0.012 | 3.35 | 1.4 | 26000 | 34000 | 0.012 |
609 | 9 | 0.3543 | 24 | 0.9449 | 7 | 0.2756 | 0.3 | 0.012 | 3.4 | 1.45 | 22000 | 30000 | 0.014 |
6000 | 10 | 0.3937 | 26 | 1.0236 | 8 | 0.3150 | 0.3 | 0.012 | 4.55 | 1.96 | 20000 | 28000 | 0.019 |
6001 | 12 | 0.4724 | 28 | 1.1024 | 8 | 0.3150 | 0.3 | 0.012 | 5.1 | 2.39 | 19000 | 26000 | 0.021 |
6002 | 15 | 0.5906 | 32 | 1.2598 | 9 | 0.3543 | 0.3 | 0.012 | 5.6 | 2.84 | 18000 | 24000 | 0.03 |
6003 | 17 | 0.6693 | 35 | 1.3780 | 10 | 0.3937 | 0.3 | 0.012 | 6.8 | 3.35 | 17000 | 22000 | 0.039 |
6004 | 20 | 0.7874 | 42 | 1.6535 | 12 | 0.4724 | 0.6 | 0.024 | 9.4 | 5.05 | 15000 | 19000 | 0.069 |
6005 | 25 | 0.9843 | 47 | 1.8504 | 12 | 0.4724 | 0.6 | 0.024 | 10.1 | 5.85 | 13000 | 17000 | 0.08 |
6006 | 30 | 1.1811 | 55 | 2.1654 | 13 | 0.5118 | 1.0 | 0.039 | 13.2 | 8.3 | 12000 | 15000 | 0.116 |
6007 | 35 | 1.3780 | 62 | 2.4409 | 14 | 0.5512 | 1.0 | 0.039 | 16 | 10.3 | 10000 | 13000 | 0.155 |
6008 | 40 | 1.5748 | 68 | 2.6772 | 15 | 0.5906 | 1.0 | 0.039 | 16.8 | 11.5 | 8000 | 11000 | 0.185 |
6009 | 45 | 1.7717 | 75 | 2.9528 | 16 | 0.6299 | 1.0 | 0.039 | 21 | 15.1 | 7200 | 9000 | 0.231 |
6010 | 50 | 1.9685 | 80 | 3.1496 | 16 | 0.6299 | 1.0 | 0.039 | 21.8 | 16.6 | 6400 | 7800 | 0.25 |
6011 | 55 | 2.1654 | 90 | 3.5433 | 18 | 0.7087 | 1.1 | 0.043 | 28.3 | 21.2 | 5700 | 7000 | 0.362 |
6012 | 60 | 2.3622 | 95 | 3.7402 | 18 | 0.7087 | 1.1 | 0.043 | 29.5 | 23.2 | 5000 | 6300 | 0.385 |
6013 | 65 | 2.9551 | 100 | 3.9370 | 18 | 0.7087 | 1.1 | 0.043 | 31.9 | 25 | 4800 | 6100 | 0.44 |
6014 | 70 | 2.7559 | 110 | 4.3307 | 20 | 0.7874 | 1.1 | 0.043 | 39.7 | 31 | 4600 | 5800 | 0.6 |
6015 | 75 | 2.9528 | 115 | 4.5276 | 20 | 0.7874 | 1.1 | 0.043 | 41.6 | 33.5 | 4400 | 5600 | 0.64 |
Basic Bearing | Bore d | Outer Diameter D | Width W | Radius r | Basic Load Rating KN | Maximum Run out Speed | Weight | ||||||
| mm | inch | mm | inch | mm | inch | mm | inch | Dynamic | Static | Grease | Oil | ||
C | CO | r/min | r/min | ||||||||||
627 | 7 | 0.2756 | 22 | 0.8661 | 7 | 0.2756 | 0.3 | 0.012 | 3.35 | 1.4 | 26000 | 34000 | 0.013 |
628 | 8 | 0.3149 | 24 | 0.9448 | 8 | 0.3149 | 0.3 | 0.012 | 4 | 1.59 | 24000 | 32000 | 0.017 |
629 | 9 | 0.3543 | 26 | 1.0236 | 8 | 0.3149 | 0.3 | 0.012 | 4.55 | 1.96 | 22000 | 30000 | 0.02 |
6200 | 10 | 0.3937 | 30 | 1.1811 | 9 | 0.3543 | 0.6 | 0.024 | 5.1 | 2.39 | 19000 | 26000 | 0.032 |
6201 | 12 | 0.4724 | 32 | 1.2598 | 10 | 0.3937 | 0.6 | 0.024 | 6.1 | 2.75 | 18000 | 24000 | 0.037 |
6202 | 15 | 0.5906 | 35 | 1.3780 | 11 | 0.4331 | 0.6 | 0.024 | 7.75 | 3.6 | 17000 | 22000 | 0.045 |
6203 | 17 | 0.6693 | 40 | 1.5748 | 12 | 0.4724 | 0.6 | 0.024 | 9.6 | 4.6 | 16000 | 20000 | 0.066 |
6204 | 20 | 0.7874 | 47 | 1.8504 | 14 | 0.5512 | 1.0 | 0.039 | 12.8 | 6.65 | 14000 | 18000 | 0.106 |
6205 | 25 | 0.9843 | 52 | 2.0470 | 15 | 0.5906 | 1.0 | 0.039 | 14 | 7.85 | 12000 | 16000 | 0.128 |
6206 | 30 | 1.1811 | 62 | 2.4409 | 16 | 0.6299 | 1.0 | 0.039 | 19.5 | 11.3 | 10000 | 13000 | 0.199 |
6207 | 35 | 1.3780 | 72 | 2.8346 | 17 | 0.6693 | 1.1 | 0.043 | 25.7 | 15.3 | 8800 | 10000 | 0.287 |
6208 | 40 | 1.5748 | 80 | 3.1496 | 18 | 0.7087 | 1.1 | 0.043 | 29.1 | 17.8 | 7700 | 9200 | 0.367 |
6209 | 45 | 1.7717 | 85 | 3.3465 | 19 | 0.7480 | 1.1 | 0.043 | 32.5 | 20.4 | 6800 | 8200 | 0.416 |
6210 | 50 | 1.9685 | 90 | 3.5433 | 20 | 0.7874 | 1.1 | 0.043 | 35 | 23.2 | 6100 | 7300 | 0.462 |
6211 | 55 | 2.1654 | 100 | 3.9370 | 21 | 0.8268 | 1.5 | 0.059 | 43.5 | 29.2 | 5500 | 6600 | 0.602 |
6212 | 60 | 2.3622 | 110 | 4.3307 | 22 | 0.8661 | 1.5 | 0.059 | 52.5 | 36 | 5000 | 6000 | 0.789 |
6213 | 65 | 2.5591 | 120 | 4.7244 | 23 | 0.9055 | 1.5 | 0.059 | 58.5 | 40.5 | 4800 | 5800 | 0.99 |
6214 | 70 | 2.7559 | 125 | 4.9213 | 24 | 0.9449 | 1.5 | 0.059 | 63.7 | 45 | 4600 | 5600 | 1.1 |
6215 | 75 | 2.9528 | 130 | 5.1181 | 25 | 0.9843 | 1.5 | 0.059 | 68.9 | 49 | 4400 | 5400 | 1.2 |
ABEC-5 TOLERANCE CLASS ABEC-5 (P5)
INNER RING | Tolerance in um/s | |||||||||||
d mm | Δdmp | Vdp²)Diameter Series | Vdmp | Kia | Sd | Sis3) | ΔBs | Vbs | ||||
9 | 0,1,2,3,4 | |||||||||||
over | including | high | low | max | 3 | max | max | max | High | Low | max | |
1)0.6 | 2.5 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -40 | 5 |
2.5 | 10 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -40 | 5 |
10 | 18 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -80 | 5 |
18 | 30 | 0 | -6 | 6 | 5 | 3 | 4 | 8 | 8 | 0 | -120 | 5 |
30 | 50 | 0 | -8 | 8 | 6 | 4 | 5 | 8 | 8 | 0 | -120 | 5 |
50 | 80 | 0 | -9 | 9 | 7 | 5 | 5 | 8 | 8 | 0 | -150 | 6 |
OUTER RING | Tolerance in um/s | |||||||||||
D mm | Δdmp | Vdp²)Diameter Series | Vdmp | Kia | SD4) SD15) | Sea4)5) | ΔBs | Vbs | ||||
9 | 0,1,2,3,4 | |||||||||||
over | including | high | low | max | max | max | max | High | Low | max | ||
1)2.5 | 6 | 0 | -5 | 5 | 4 | 3 | 5 | 8 | 8 | 5 | ||
6 | 18 | 0 | -5 | 5 | 4 | 3 | 5 | 8 | 8 | 5 | ||
18 | 30 | 0 | -6 | 6 | 5 | 3 | 6 | 8 | 8 | 5 | ||
30 | 50 | 0 | -7 | 7 | 5 | 4 | 7 | 8 | 8 | 5 | ||
50 | 80 | 0 | -9 | 9 | 7 | 5 | 8 | 8 | 10 | 6 | ||
80 | 120 | 0 | -10 | 10 | 8 | 5 | 10 | 9 | 11 | 8 | ||
120 | 150 | 0 | -11 | 11 | 8 | 6 | 11 | 10 | 13 | 8 | ||
ABEC-7 TOLERANCE CLASS ABEC-7 (P4)
INNER RING | Tolerance in um/s | ||||||||||||||
d mm | Δdmp | Δds | Vdp²)Diameter Series | Vdmp | Kia | Sd | Sia | ΔBs | Vbs | ||||||
7,8,9 | 1,7,2,3,4 | ||||||||||||||
over | including | high | low | high | low | max | max | max | max | max | High | low | Low | max | |
1)0.6 | 2.5 | 0 | -4 | 0 | -4 | 4 | 3 | 2 | 2.5 | 3 | 3 | 0 | -40 | -40 | 2.5 |
2.5 | 10 | 0 | -4 | 0 | -4 | 4 | 3 | 2 | 2.5 | 3 | 3 | 0 | -40 | -40 | 2.5 |
10 | 18 | 0 | -4 | 0 | -4 | 4 | 3 | 2 | 2.5 | 3 | 3 | 0 | -80 | -80 | 2.5 |
18 | 30 | 0 | -5 | 0 | -5 | 5 | 4 | 2.5 | 3 | 4 | 4 | 0 | -120 | -120 | 2.5 |
30 | 50 | 0 | -6 | 0 | -5 | 6 | 4 | 3 | 4 | 4 | 4 | 0 | -120 | -120 | 3 |
50 | 80 | 0 | -7 | 0 | -5 | 7 | 5 | 3.5 | 4 | 5 | 5 | 0 | -150 | -150 | 4 |
OUTER RING | Tolerance in um/s | ||||||||||||||
D mm | Δdmp | Δds | Vdp²)Diameter Series | Vdmp | Kia | Sd | Sia | ΔBs | Vbs | ||||||
7,8,9 | 1,7,2,3,4 | ||||||||||||||
over | including | high | low | high | low | max | max | max | max | max | High | low | max | ||
1)2.5 | 6 | 0 | -4 | 0 | -4 | 4 | 3 | 2 | 3 | 4 | 5 | Identical to ΔBs and VBs of inner ring of same bearing | 2.5 | ||
6 | 18 | 0 | -4 | 0 | -4 | 4 | 3 | 2 | 3 | 4 | 5 | 2.5 | |||
18 | 30 | 0 | -5 | 0 | -5 | 5 | 4 | 2.5 | 4 | 4 | 5 | 2.5 | |||
30 | 50 | 0 | -6 | 0 | -6 | 6 | 5 | 3 | 5 | 4 | 5 | 2.5 | |||
50 | 80 | 0 | -7 | 0 | -7 | 7 | 5 | 3.5 | 5 | 4 | 5 | 3 | |||
80 | 120 | 0 | -8 | 0 | -8 | 8 | 6 | 4 | 6 | 5 | 6 | 4 | |||
120 | 150 | 0 | -9 | 0 | -9 | 9 | 7 | 5 | 7 | 5 | 7 | 5 | |||
Application Senarios of high precision ball bearings
Customization welcomed:
We can printing your brand (logo,artwork)on the shield or laser engraving your brand on the shield.
We can custom your packaging according to your design.
All copyright owned by clients and we promised don't disclose any information.
Packing and Shipping:
The deep groove ball bearings will be securely packaged individually, or tube packing or packed as customization packing
Shipping method is negotiable.
FAQ:
1.Q:Are you a factory or trading company?
A:Kent Bearing is specialized in manufacturing and exporting bearings, and we have our own factory and warehouse.
2.Q:Can I get some samples and do you offer free samples?
A:Yes, sure, Kent Bearing are honored to offer you samples.
3.Q: How about the shipping?
A: We can arrange the shipment or you may have the forwarder.
4.Q: Could you tell me the material of our bearing?
A: We have chrome steel, and stainless steel, ceramic and plastic material
5.Q: Can we get support if we have our own market position?
A: Please inform us detailed information about your market,we will discuss
and propose helpful suggestion for you and to find the best solution for you.